The Linksys E7350 Dual-Band WiFi 6 EasyMesh™ Router lets you enjoy the power of Wi-Fi® technology. It delivers enhanced speed, range, and security for all your networking needs which allows you to swiftly stream HD videos, surf, email, play games online, and chat.
The Wi-Fi settings on the web interface of Linksys E7350 allows you to configure and protect your network from security vulnerabilities through managing your WiFi credentials. To access this page, log in to the router's web interface. For instructions, click here. Then, go to Configuration > Wi-Fi.
The Wi-Fi settings on the web interface of Linksys E7350 allows you to configure and protect your network from security vulnerabilities through managing your WiFi credentials. To access this page, log in to the router's web interface. For instructions, click here. Then, go to Configuration > Wi-Fi.
Overview of the Wi-Fi page
Feature
|
Description
|
Basic Wireless Settings
|
This page allows you to configure the WiFi settings of your network. EasyMesh The EasyMesh technology allows your router to add a Linksys EasyMesh child node to extend your WiFi and be compatible with other Linksys EasyMesh-supported devices. With the latest firmware, the EasyMesh is enabled after running the setup wizard. If your router has older firmware, the feature is turned OFF by default.
5 GHz Wireless Settings The following are available options for Linksys E7350. NOTE: When the router is in EasyMesh mode, Mixed(A/N/AC/AX) is the only supported option. EasyMesh enabled EasyMesh disabled 2.4 GHz Wireless Settings The following are available options for Linksys E7350. NOTE: When the router is in EasyMesh mode, Mixed(B/G/N/AX) is the only supported option. EasyMesh enabled EasyMesh disabled Channel Width
This option is only available when EasyMesh is not enabled. The default value is Auto. Below are the other supported options. 5 GHz
2.4 GHz Channel The recommended channel setting is Auto. SSID The SSID is the WiFi name. When you change the SSID on the parent node, the new SSID will sync to the connected child nodes. The clients will need to reconnect to the new WiFi name. Check the box to broadcast your SSID. To save your settings, scroll down to the bottom and click Save. |
Wi-Fi Protected Setup
|
With the latest firmware, the Wi-Fi Protected Setup™ (WPS) feature is enabled after running the setup wizard. This is for the child nodes that will be added later. The WPS checkbox is greyed out and cannot be turned OFF since WPS pairing is needed when adding child nodes. If you want the WPS turned OFF, disable the EasyMesh feature first. Pressing the WPS button for 3 seconds or less, or just a tap will initiate pairing between the node and a WPS client. Pressing it for more than 3 seconds will initiate the pairing with a child node. NOTE: The WPS feature cannot be used when your router’s Broadcast SSID is disabled, any of your radio bands are disabled, or if MAC Filtering is enabled. |
Wireless Security
|
You can configure your WiFi security settings on the Wireless Security page. The default security option for both 2.4 GHz and 5 GHz bands is WPA2 Personal. EasyMesh enabled
EasyMesh disabled |
Guest Access
|
You can enable or disable the Guest Network on the Guest Access page. This is supported on both parent and child nodes. The Guest Password consists of four to 32 characters, and up to 10 guests are allowed. To update the Guest Password, click on Change. Once you're done configuring your Guest Network, click Save. The Guest name uses the main WiFi name with -guest appended to the end. |
Wireless MAC Filter |
Click on the box before Wireless MAC Filter to enable or disable it. Then, choose whether this will prevent or permit the computers listed on the MAC Address Filter List to access your WiFi. You can enter up to 32 MAC addresses or click on the Wireless Client List to register the MAC address of the device that is already connected to your WiFi. Then, click the Save button found at the bottom part of the page when you’re done. The Wireless Client List provides the following options:
|
Advanced Settings
|
The Beamforming feature of your router is enabled by default. This is the recommended setting. You may update this and click on Save. |