
The Linksys SPNMX57CF-UK supports the latest Wi-Fi® 6 (802.11ax) standard to deliver lag-free and simultaneous streaming to any device. With the powerful WiFi 6 Mesh coverage, it is designed to deliver gigabit WiFi speeds to every corner of your home, including the backyard and outdoor smart home devices.
This model is only for Community Fibre subscribers in the United Kingdom.
HARDWARE INFORMATION
- Community Fibre logo on the node
- Default WiFi name: CommunityFibre10Gb_xxxxx printed on the product label
- Product label: SPNMX57
- Packaging label: SPNMX57CF
- Ports 1 and 2 are at 1 Gbps, and port 3 is at 2.5 Gbps
Ports:
- Gigabit ethernet ports:
- Port 1 at 1 Gbps
- Port 2 at 1 Gbps
- Port 3 at 2.5 Gbps
- A multi-gigabit internet port at 2.5 Gbps
- Power port (12V, 2A)
Buttons and switch:
- Reset button
- Pair button
- One power switch (sliding)
These are the features of the Linksys SPNMX57CF-UK.
- IEEE 802.11ax
- AX5400 Dual-Band
- 2x2 + 4x4 Spatial streams
- Backward compatible with 802.11 a/b/g/n/ac
- 1 GHz dual-core processor
- Intelligent Mesh™
- Easy Setup
- Band steering
- Bluetooth® 4.0/LE
- WiFi security
- Guest network
- Parental Controls
- Port forwarding
- Supports parent and child mode
- Supports Automatic Setup via Auto Configuration Server (ACS)
- Supports DHCP
- Supports VPN Passthrough IPsec, PPTP, L2TP
- DDNS is supported via the web browser
- Supports TR-069
- Pair button to add child nodes
- The default IP address is 192.168.1.1.
- If the upstream device uses the same IP address, the node will automatically use a different LAN IP address to avoid any conflict.
- The default Guest network IP address range is 192.168.3.x.
- The default administrator password is the default WiFi password, which is located on the product label.
- The default WiFi name and password are found at the bottom of the node. The default WiFi name is CommunityFibre10GB_xxxxx (where xxxxx represents the last five hexadecimal digits of the node’s MAC address).
- Each node has a unique pre-assigned WiFi password (located at the bottom of the node).
- The default Guest WiFi name is CommunityFibre10GB_xxxxx–guest (where xxxxx represents the last five hexadecimal digits of the node’s MAC address).
- The Guest network is disabled by default. It can be enabled using the router's web interface or the Linksys app.
- DFS support is disabled by default on the 5 GHz radio.
SETUP AND INSTALLATION
- A modem or gateway with an active internet connection by Community Fibre
- The latest version of a web browser
Additionally, a node that is not from Community Fibre may be added to your network so long as it is set up as a child node and not as the parent node.
- WPA2™/WPA3™ Mixed Personal
- WPA3 Personal
- WPA2 Personal
- Enhanced Open Only
- Open and Enhanced Open Only
- Open
FIRMWARE UPGRADE
ADVANCED CONFIGURATION
To learn how to access your dashboard, click the links below:
iOS and Android
Web interface using a computer
Make sure that a bright red flash, followed by three to four quick faded red pulses, then another bright red flash occur before you release the button.
TROUBLESHOOTING
DO NOT try to set up the parent node with the Linksys app while the node is going through the Automatic setup, because the Linksys app will not detect the node. Wait until the node is configured and the status light is solid blue before you can use the Linksys app to manage your network.